Heating Repair, Installation & Maintenance
No Heat? Call Premier.
Furnace and heating system service across the Greater Los Angeles area. We diagnose the actual issue before recommending a fix, and walk you through it in plain terms.
How It Works
How a Service Call Works
-
Call or request service
Call (626) 791-0001 or send a request. We're open Monday to Friday, 7:30 AM to 4:30 PM.
-
We diagnose the problem
A technician finds the actual cause before recommending a fix.
-
Approve the cost, then we fix it
We walk through the scope and cost with you before any work begins.
Heating Repair
A furnace that won't ignite, short cycles, or runs without producing heat usually points to one of a handful of causes: an ignition or flame sensor problem, a failing blower motor, a clogged filter, or a thermostat that has lost communication with the system.
We diagnose the system before replacing parts, so the repair addresses the actual failure instead of guessing at it.
Signs your heating needs repair
- Furnace won't turn on or ignite
- Blows cold air or cycles too often
- Strange smells, noises, or rising gas bills
- Pilot light or ignition system failures
Heating Repair FAQs
Why won't my furnace turn on?
The most common causes are an ignition or flame sensor problem, a tripped safety switch, a thermostat communication issue, or a blower motor failure. A diagnostic visit identifies which one applies before any parts are replaced.
Why is my furnace blowing cold air?
This usually points to an ignition failure, a clogged filter restricting airflow, or a thermostat set incorrectly. It can also signal a cracked heat exchanger, which we check as a safety matter, not just a comfort issue.
Is it normal for a furnace to smell when it first turns on for the season?
A brief, mild odor from dust burning off is common the first time a furnace runs after months of inactivity. A persistent or strong smell, especially anything resembling gas, warrants an immediate service call.
Do you repair both gas and electric heating systems?
Yes, our technicians diagnose and repair both gas furnaces and electric heating systems.
Furnace Installation
An aging furnace is more than a comfort issue. Efficiency drops, repair parts get harder to source, and the risk of a mid-winter breakdown goes up every season. We evaluate whether repair still makes sense before recommending a full replacement.
New installations are sized to the home's actual heating load and matched to the existing or updated ductwork, with attention to venting and combustion safety on every gas furnace we install.
What to expect with a new furnace
- Straight-talk assessment of repair versus replacement
- Sized to the home's heating load, not just the old unit
- Venting and combustion safety checked on every install
- Manufacturer warranty registration handled for you
Furnace Installation FAQs
How do I know if I should repair my furnace or replace it?
We weigh the age of the unit, the cost of the repair, and how often it has broken down, and give you a straight comparison against the cost of replacement rather than defaulting to a sale.
How long does furnace installation take?
Most replacements are completed in a single day. Jobs that involve ductwork or venting changes take longer, and we review the timeline with you before work starts.
Will a new furnace lower my energy bills?
A properly sized, higher-efficiency furnace typically uses less fuel than an aging unit to produce the same heat, though the exact savings depend on the home and the system being replaced.
Do you handle the permits for a furnace replacement?
Yes, permitting and inspection are handled as part of the installation where required.
Furnace Maintenance
Most furnace breakdowns trace back to something a tune-up would have caught: a dirty flame sensor, a failing igniter, a clogged filter restricting airflow. A visit before heating season is when those get found, not during the first cold night of the year.
A maintenance visit covers the burner assembly, ignition system, blower motor, and safety controls, with a straightforward report on anything that needs attention.
What to expect from furnace maintenance
- Annual tune-up recommended before heating season
- Burner, ignition, and safety control inspection
- Blower motor and electrical connection checks
- Filter and airflow inspection
Furnace Maintenance FAQs
How often does a furnace need maintenance?
Once a year, ideally in fall before heating season starts, is enough for most residential systems. Furnaces that run heavily through a long heating season, or that are already past 10 years old, benefit from a closer look each year rather than skipping one.
What happens during a furnace tune-up?
A technician inspects the burner assembly and ignition system, checks the heat exchanger and venting, tests safety controls, and inspects the filter and airflow. Anything that needs attention gets reported before it becomes a no-heat call.
Does furnace maintenance really prevent breakdowns?
Many of the most common furnace failures, ignition problems, a failing blower motor, a clogged filter, are exactly the kind of issues a maintenance visit is designed to catch before the system fails.
Is maintenance worth it on an older furnace I might replace soon?
Often yes. A tune-up is inexpensive relative to an emergency repair, and it can tell you whether the furnace is likely to make it through another winter or whether planning for replacement makes more sense.
Request Service
Request a Quote
Not Sure Which Service You Need?
Call (626) 791-0001 and we'll help you figure it out.
Call (626) 791-0001Serving the Greater Los Angeles area
- Pasadena
- Altadena
- Monrovia
- Arcadia
- San Marino
- La Cañada Flintridge
- Eagle Rock
- South Pasadena
- Alhambra
- San Gabriel
- Glendale
- La Crescenta-Montrose
Based in Pasadena, serving homes and businesses throughout the San Gabriel Valley and beyond.